PART 2 PRODUCT

2.01 Manufacturer/Equipment:

MODEL TYPE: Garaventa Genesis Vertical Lift with; (specify) 1041 mm (41"), 1448 mm (57"), 1829 mm (72"), 2438 mm (96"), 3048 mm (120"), (or) 3658 mm (144") lifting height and with (specify) 915 mm x 1372 mm (36"x54"), 915 mm x 1524 mm (36"x 60") or 1067 mm x 1524 mm (42"x60") platform (for 90 degree exit) manufactured by Garaventa (Canada) Ltd., Surrey, B.C. distributed by _____________________________ configured as follows:

1. Machine Tower: Custom aluminum extrusion – Anodized champagne finish.
2. Base Frame: 76 mm X 51 mm X 6 mm (3" x 2" x .25") structural steel angle.
3. Platform side guard panels: 16 gauge galvanized steel sheet panels. Custom anodized aluminum extrusion tubing frame.
4. Enclosure Panel: 16 gauge galvanized steel sheet, acrylic panels (optional)
5. Platform and Access Ramp: 16 gauge galvanized steel plates; slip-resistant surfaces.
6. Coatings/Surfacing: Finished in process consisting of alkaline detergent wash, clear water rinse, iron phosphate coating, clear water rinse, non-chromate rinse, and baked polyester electrostatically applied for indoor/outdoor use.
7. Drive self-lubricating acme drive nut and screw gear belt pulleys with gearbelt.
8. Emergency operation: Dual emergency lowering options: (1) Battery powered emergency lowering device capable of lowering platform or (2) Manual lowering device capable of raising or lowering platform in event of power or component failure.
9. Capacity: Maximum 341 kg. (750 lbs.) operating load, with a minimum safety factor certified to meet or exceed the standards of 1.02 above.
10. Lifting Height: (to suit) (3658 mm/144" maximum).
11. Travel Speed: 3.35 meters/minute (11 feet per minute).
12. Motor: 208-240 VAC, 60Hz., 8 amp, single phase with minimum ¾ HP., and 1,750 RPM instant reverse capability. Lift shall stop automatically at desired landings.
13. Panel color: RAL# 7030 – Stone Grey. (Optional colors are available from manufacturer).
14. 2032 mm (6’8") flush mount door with self-closer at bottom landing and (specify) 2032 (6’8") flush mount door or 1067 mm (42") gate with self-closer at upper landing.
15. 1067 mm (42") side guard panels on platform.
16. Safety Devices:

1. Platform lighting integral to the platform control panel, automatically activated during travel and for at least 8 seconds after platform arrives at the designated landing.
2. Service key bypass system to allow door interlocks and safety nut to be bypassed in order to safely evacuate stranded users.
3. Grounded electrical system with upper, lower, and final limit switches and 24 VDC operating controls.
4. Non-slip platform and access ramp surfaces.
5. Security key-locks on controls meeting access limitation requirements of ASME A17.1, Section 2000.
6. Interlocks electrically monitor that the door is in the closed position and that the deadbolt is engaged. The interlock cannot be defeated without special tools. This ensures that the lift cannot travel until all safeties are engaged.
7. Integral safety nut assembly with safety switch.
8. Emergency stop switch which shuts off power to lift and activates audio alarm.
9. Pit stop switch mounted on base frame (optional).

2.02 APPLICABLE STANDARDS

Lift shall be designed and manufactured in accordance with the following standards:

1. American Society of Mechanical Engineers/ American National Standards Institute (ASME/ANSI) A.17.1, Section 2000 for vertical wheelchair lifts in private and public places.
2. National Electric Code (NEC).
3. American Society for Testing Materials (ASTM).
4. Canadian Welding Bureau (CWB).
5. Americans with Disabilities Act (ADA).

Wiring:

Electrical contractor shall provide electrical piping and wiring. Lift contractor will make final electrical connections.

Controls:

24VDC constant pressure directional buttons on platform and On/Off key switches at landings and on platform. Emergency stop on platform.